5x205 Black eBrake Non-Wilwood Caliper | Classic VW Type 1 Rear Long Axle Disc Brake Conversion Kit - Swing Axle Long Spline - fits 1968 Classic VW Type 1 Beetle Ghia

⭐️⭐️⭐️⭐️⭐️ - "Modern stopping power for your Classic VW—BAD Series Disc Brake Kit is Made in USA, lifetime warrantied, bolt pattern adjustable, and fully complete." - ⭐️⭐️⭐️⭐️⭐️

Key Benefits

• Made in the USA – Precision CNC machined for quality and reliability.

• Lifetime Warranty – If you ever wear out a rotor, we’ll replace it.

• Change Lug Patterns in Minutes – Future wheel swaps are quick and easy.

• Complete & Time-Saving – Everything you need for a correct install is included. Just add lug nuts and DOT 3 brake fluid.

Compatibility

• 1968 Type 1 Beetle's/Karmann Ghia's - Long Axle Long Spline - Don't know what you have, check out this article.

• Kit cars with long axle long spline swing axle suspension

• Baja's

Why choose BAD Series Disc Brakes?

Classic Volkswagens weren’t built for today’s highways. The stopping distances simply aren’t enough for modern traffic. The BAD Series Disc Brake Kit brings your VW up to today’s safety standards with American-made quality that’s engineered to last.

Our Gen 2 BAD Series rotors are built in three pieces (hub, bolt pattern, rotor) so you can swap bolt patterns without replacing the whole assembly. Pair them with the right calipers, brackets, and stainless steel hoses, and you have one of the most complete, reliable kits on the market.

How To

• Install Guide - Link

• Packing Lists

Recommendations

• Use an air impact to tighten the rear rotors, not a torque tool as per install guide instructions

What's Included

• Gen 2 BAD Series rotor assemblies
• Premium Grease Seal Kits
• Caliper Brackets
• Calipers/pads
• Mounting hardware, shims and loctite
• Stainless Steel Brake Hoses
• Gen 2 billet grease caps with hardware, anti-seize and Allen wrenches
• Axle Nuts
• Chromoly spacers for rotors
• Billet Cable Clamps
• Billet Axle Bearing Clamps
• Cotter Pin Replacement Bolts
• eBrake Cables with stainless hardware (if selected)

(Everything needed for the job done right. You’ll just need lug nuts and DOT 3 brake fluid.)

FAQ

Q: Does this kit add track width?
A: No.

Q: Will my wheels fit over your grease cap? 
A: Yes & No. Depending on the wheels, there is a ton of them, the front grease caps could interfere with the center caps. Best advice I can give you is before you install the brake kit, install the cap onto the rotor, and with the wheel face down, place the rotor into the wheel. If it clears, you can install the brake kit. If it doesn't, you need our shallow caps. Please contact us here, and we will initiate a swap with you. 

Q: What size and length are your studs?
A: 14mm x 1.50 - 1.500" in length. We do have 12mm x 1.50 studs available that will fit into the same bolt pattern we supply you. Press out and press in. You can find out what studs are recommended for your application here.

Q: Why do you make the studs so long?
A: Fitment of wheels on your ride is personal. Versatility is the answer. If you want a wheel to fit the way you envision, it might require a spacer or two. Airkewld will be offer wheel spacers in various widths. There might be a unique lug nut you want to use and the studs is too long. Trim it up to make it work for your application. 

Q: My brakes are squealing, how can I resolve this?
A: In our supplied install guide, there is a section on bedding in the rotors. If you bed in the rotors correctly, noises will be non-existent. If you don't get it the first time, scuff the rotors where the pads touch along with the pad surface, clean it with brake clean and do the process again until you get it right. Simple process really. 

Q: I want to change out my bolt pattern, how can I do that? 
A: Your install guide will go over the process in detail. It will require you to break loose the allen bolts attaching the bolt pattern to the hub assembly, and installing the new one and torquing it down correctly.